titan fitness pull up bar This is a topic that many people are looking for. savegooglewave.com is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, savegooglewave.com would like to introduce to you Titan Fitness Pull up bar INSTALL. Following along are instructions in the video below:
We installed this pull up bar in our guest bedroom in our apartment. And for for the time being i will refer to these two side pieces. As the brackets took a lot of measuring here.
What im doing is measuring from an outlet over 16 inches to find the studs and i would recommend putting this in studs. Highly recommend here im using the nail technique to push through the drywall to find where the studs are one thing you can count on is a stud being on one side or the other of an outlet in your house. And that was the case here on the right side because they need to attach the outlet box to something behind the drywall and so that you can pretty much count on a stud always being there and i measured from that stud to the left 16 inches to find the other stud.
So here im measuring from the adjacent wall over to where i know the stud. The stud is and then im carrying that measurement.
I think it was 95 inches. Im carrying that measurement up the wall because the studs run vertically and i know if theres a stud at ninety five inches at the base of the wall that same stud is 95 inches from the adjacent wall. Even if i go to head height or all the way to the ceiling.
Its always going to be there here. Im measuring from that 95 inch mark. Now to the right 48 inches.
Because the studs run 16 30. To 40 inches on center.
So again just confirming with that nail method cold pounding the nail through the drywall to make sure. The stud is there here. Were trying to position the brackets up up and down vertically.
Just kind of put a mark on the wall. There measure. It i think it was 59 inches bring it over to where the other ones going to be put a mark on the wall.
At 59 inches pulling it back up here this was crucial because we wanted it level kind of right and left. I was marking the holes to pre drill for the lag bolts again doing the same thing on the other side.
We had our bike stored on the left side. So this was a little bit tricky because lauren was right in the way. But she was very helpful so again these are for pre drilling.
The holes for lag bolts again just making sure the holes are dead center. Where i wanted them measure twice cut once measure twice drill once so what im saying. Here basically is we use three eighths by four inch lag bolts to and i came up with the four inches long.
The metal on the brackets was an inch and a quarter wide accounting for 3 4. Inch of drywall and then that leaves us two inches to go into the stud on the other side.
And there are three per bracket using this impact driver really really helped out a lot really noisy. But again since we had lined these brackets up perfectly level. We didnt need to you dont need to put a level back on them to make sure that theyre straight up and down put any other bracket up this process was pretty easy.
Its nice having the right tools and then i went back with a ratchet with the same. I believe it was a 7 16. Socket and just hand tightened the last revolution or two on these.
Its tough to to know what torque youre tightening bolts down to with a impact driver. So i just wanted to do the last couple revolutions by hand and then the last step is putting the bar through see. Theres theres two bolts on the theres one bolt on a top side of each of the brackets and i had to loosen those up and then i went to the ratchet and just tighten those just an tight or a little bit more those arent really a big deal.
So once those were tight get the chair out of the way and see what happens and you know im a hundred eighty pounds and you know its not bending at all you know were not going to be were not going to be jumping around too much on these so yeah. It worked and let me know if you have any questions guys. .
Thank you for watching all the articles on the topic Titan Fitness Pull up bar INSTALL. All shares of savegooglewave.com are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.